Emerson 0478-0047-03 User Manual Download Page 20 | Manualshive

Page: 20 / 40

background image

How to use this

20

SI-I/O User Guide

Issue Number: 3

This parameter controls the logic for all the digital inputs on the module.

The I/O Read Word (Pr

S.01.010

) reflects the state of digital I/O 1 - 8. Each bit matches the value of the state parameter for the respective digital input

or output so the bit value for the digital inputs will be the state of the actual input before any inversion selection is applied. The bit value for the digital
output will include the state inversion if selected in the invert parameter for the output.
The table below shows how the bits correspond to each function.

Digital I/O 1-4 are the standard I/O that are compatible with IEC61131-2 logic levels. When the channel mode is set to zero, the I/O is configured as a
digital input. When the channel mode is set to one, the I/O is configured as a digital output.

S.01.008

Digital I/O Logic Polarity

Minimum

0

Maximum

1

Default

1

Units

Type

8 Bit User Save

Update Rate

Background read

Display Format

None

Decimal Places

0

Coding

RW, TE

Value

Text

Description

0

Negative Logic

Negative Logic

1

Positive Logic

Positive Logic

S.01.009

Open Collector Output

Minimum

0

Maximum

1

Default

0

Units

Type

8 Bit User Save

Update Rate

Background read

Display Format

None

Decimal Places

0

Coding

RW, TE

Value

Text

Description

0

Push-pull

Push-pull output

1

Open Collector

Open Collector output

S.01.010

I/O Read Word

Minimum

0 (Display
00000000)

Maximum

255 (Display
11111111)

Default

0

Units

Type

16 Bit Volatile

Update Rate

Background read

Display Format

None

Decimal Places

0

Coding

RO

Bit

7

6

5

4

3

2

1

0

Terminal

T11

T9

T8

T7

T5

T4

T3

T2

Terminal

description

Digital

Input 8

Digital

Input 7

Digital

Input 6

Digital

Input 5

Digital

I/O 4

Digital

I/O 3

Digital

I/O 2

Digital

I/O 1

S.01.011

T2 Digital I/O 1 Mode

S.01.012

T3 Digital I/O 2 Mode

S.01.013

T4 Digital I/O 3 Mode

S.01.014

T5 Digital I/O 4 Mode

Minimum

0

Maximum

1

Default

0

Units

Type

8 Bit User Save

Update Rate

Background read

Display Format

None

Decimal Places

0

Coding

RW, TE

Value

Text

Description

0

Digital Input

Digital Input

1

Digital Output

Digital Output

«
...
18
19
20
21
22
...
»

Summary of Contents for 0478-0047-03









































Reviews:

No comments

Related manuals for 0478-0047-03

Brand: OmarLift Pages: 14

Brand: UNITED Pages: 8

Brand: TA Hydronics Pages: 14

Brand: BADODOSECURITY Pages: 8

Brand: Kasco Pages: 3

Brand: Datalogic Pages: 15

Brand: UNICORECOMM Pages: 32

Brand: UNICORECOMM Pages: 7

Brand: UNICORECOMM Pages: 26

Brand: UNICORECOMM Pages: 25

Brand: V2 Pages: 12

NORA-W10 Series

Brand: u-blox Pages: 56

Brand: z21 Pages: 2

Brand: ABB Pages: 17

Brand: Tech 21 Pages: 2

Brand: Mitsubishi Pages: 30

Brand: Fibocom Pages: 79

Brand: oventrop Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands