Emerson 0478-0047-03 User Manual Download Page 21 | Manualshive

Page: 21 / 40

background image

How to use this

SI-I/O User Guide

21

Issue Number: 3

Terminals 7 and 8 can be configured as digital inputs, analog voltage inputs or a single differential analog input.

When Pr

S.01.015

or Pr

S.01.016

are set to Digital Input (0), terminals T7 or T8 will be configured as digital inputs.

When Pr

S.01.015

or Pr

S.01.016

are set to Volt IN (1), terminals T7 or T8 will be configured as independent single ended analog voltage inputs.

When either Pr

S.01.015

or Pr

S.01.016

are set to Differential (2), the terminals T7 and T8 are combined so that they can be used as a high precision

differential analog voltage input with T7 as the positive input and T8 as the negative input. This will disable the single ended analog voltage input
parameters and they will not update.
A combination of setting these parameters to either Digital Input (0) or Volt IN (1) is permitted between the two terminals so that one terminal can be
used as digital input and the other can be configured as a single ended analog voltage input.
Setting either of these parameters to Differential (2) will override any other value in the other mode parameter to configure both inputs as a single
differential analog input.

The value of Differential (2), is only available with SI-I/O firmware V01.00.01.xx and later. To use the differential analog input in previous firmware,
Pr

S.01.015

and Pr

S.01.016

must both be set to Volt IN (1).

Terminal 9 can be configured as a digital input, an analog voltage input or an analog current input.
The table below shows all possible values of Pr

S.01.017

.

Terminal 11 can be configured as a digital input, an analog voltage output or an analog current output.

S.01.015

T7 Digital Input 5, Analog Input 1 Mode

S.01.016

T8 Digital Input 6, Analog Input 2 Mode

Minimum

0

Maximum

1

Default

1

Units

Type

8 Bit User Save

Update Rate

Background read

Display Format

None

Decimal Places

0

Coding

RW, TE

Value

Text

Description

Function of T7

Function of T8

0

Digital Input

Digital Input

Digital Input 5

Digital Input 6

1

Volt IN

Analog Voltage Input

Analog Input 1

Analog Input 2

2

Differential

Differential Analog
Voltage Input

Positive Differential
Analog Input

Negative Differential
Analog Input

NOTE

S.01.017

T9 Digital Input 7, Analog Input 3 Mode

Minimum

0

Maximum

11

Default

1

Units

Type

8 Bit User Save

Update Rate

Background read

Display Format

None

Decimal Places

0

Coding

RW, TE

Value

Text

Description

0

Digital Input

Digital Input 7

1

Volt IN

±10 V Analog voltage Input

2

4-20 mA Low 4-20 mA switching to equivalent of 4 mA input current on loss

3

20-4 mA Low 20-4 mA switching to equivalent of 20 mA input current on loss

4

4-20 mA Hold 4-20 mA hold at level before loss on loss

5

20-4 mA Hold 20-4 mA hold at level before loss on loss

6

0-20 mA

0-20 mA

7

20-0 mA

20-0 mA

8

4-20 mA Trip

4-20 mA trip on loss

9

20-4 mA Trip

20-4 mA trip on loss

10

4-20 mA

4-20 mA no action on loss

11

20-4 mA

20-4 mA no action on loss

S.01.018

T9 Digital Input 8, Analog Output 1 Mode

Minimum

0

Maximum

5

Default

1

Units

Type

8 Bit User Save

Update Rate

Background read

Display Format

None

Decimal Places

0

Coding

RW, TE

«
...
19
20
21
22
23
...
»

Summary of Contents for 0478-0047-03









































Reviews:

No comments

Related manuals for 0478-0047-03

Brand: Eaton Pages: 166

Brand: Warren Controls Pages: 16

Brand: Newport Pages: 417

Brand: Game ready Pages: 24

Total Access 351 Series

Brand: ADTRAN Pages: 4

SUPERSTAR E-3000/F2

Brand: praher Pages: 10

Brand: IDEC Pages: 97

Brand: Bard Pages: 102

Brand: Vestil Pages: 6

Wattstopper LMIN-104

Brand: LEGRAND Pages: 22

Security Center AZ5140

Brand: Abus Pages: 16

Brand: Kelly Pages: 32

Brand: Eazyzap Pages: 32

Brand: Hansen Pages: 4

Brand: Task Force Tips Pages: 8

Brand: Steren Pages: 54

Brand: Himax Pages: 54

AGCO RoGator Hawkeye C Series

Brand: Raven Pages: 64

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands