background image

4

HULK Power Air Compressors

4

8. 

OUTPUT AIR PRESSURE GAUGE - 

Shows the pressure of the air as it leaves the 

compressor.

9. 

HAnDLE -  

Convenient, rubber gripped handle allows for 

easy transport of your air compressor.

10. 

AIR REGULATOR -  

The air regulator controls the output air 

pressure. Turn regulator clockwise to increase 

air pressure, counter-clockwise to decrease air 

pressure.

11. 

AIR COUPLER -  

Convenient brass quick-disconnect air coupler 

allows for fast easy connection to an air hose.

Safety Information

This manual contains very important information to

know and understand. This is provided for SAFETY

and to PREVENT EQUIPMENT PROBLEMS. To help 

understand this information, observe the following:

Danger indicates an imminently 

hazardous situation which, if not 

avoided, will result in death or serious injury.

Warning indicates a potentially 

hazardous situation which, if not 

avoided, could result in death or serious injury.

Caution indicates a potentially 

hazardous situation which, if not 

avoided, may result in minor or moderate injury.

Notice indicates important information, 

that if not followed, may cause damage 

to equipment.

  Read all manuals included with this 

product carefully. Be thoroughly 

familiar with the controls and the 

proper use of the equipment.

CALIfORnIA PROPOSITIOn 65

This product or its power cord 

may contain chemicals known to 

the State of California to cause cancer and birth 

defects or other reproductive harm. Wash hands 

after handling.

Basic Guidelines

1.  Allow only trained, authorized persons who 

have read and understood these operating 

instructions to use this compressor. Failure 

to follow the instructions, procedures and 

safety precautions in this manual can result in 

accidents and injuries.

2.  NEVER start or operate the compressor 

under unsafe conditions. Tag the compressor, 

disconnect and lock out all power to it to 

prevent accidental start-up until the condition 

is corrected.

3.  Install, use and operate the compressor only 

in full compliance with all pertinent OSHA 

regulations and all applicable Federal, State & 

Local Codes, standards and regulations.

DANGER

WARNING

CAUTION

NOTICE

MANUAL

WARNING

4.  NEVER modify the compressor and/or 

controls in any way.

5.  Keep a first aid kit in a convenient place. Seek 

medical assistance promptly in case of injury. 

Avoid infection by caring for any small cuts 

and burns promptly.

Breathable Air

1.  NEVER use air from this compressor for 

breathable air except in full compliance with 

OSHA Standards 29 CFR 1910 and any other 

Federal, State or Local codes or regulations.

Death or serious injury can result 

from inhaling compressed air 

without using proper safety 

equipment. See OSHA standards 

on safety equipment. 

2.  DO NOT use air line anti-icer systems 

in air lines supplying respirators or other 

equipment used to produce breathable air. 

DO NOT discharge air from these systems in 

unventilated or other confined areas.

Pressurized Components

1.  This equipment is supplied with a ASME 

designed pressure vessel protected by an 

ASME rated relief valve. Pull the ring before 

each use to make sure the valve is functional. 

DO NOT attempt to open valve while the 

machine is under pressure.

2.  Improper maintenance could lead to the air 

tank bursting or exploding.
3.  Drain air tank after each use or 

daily to prevent moisture buildup in the 

air tank. Rust can weaken the air tank 

and cause leaks or bursting. If rust is 

detected, replace tank immediately. 

4.  Do not attempt repairs to the air tank by 

welding, drilling or other modifications. Such 

modifications may weaken the air tank and 

cause a hazardous condition.

5.  If the air tank develops a leak, replace it 

immediately. Never repair, weld or make 

modifications to the air tank or its attachments.

6.  Do not make adjustments to the factory-set 

pressures.

7.  Never exceed attachments' manufacturer's 

maximum-allowable pressure rating.

8.  Do not use plastic pipe or lead tin solder 

joints for a discharge line as the may not 

withstand the high heat developed during air 

compression.

Personal Protective Equipment

Be sure all operators and others around the

compressor and its controls comply with all 

applicable OSHA, Federal, State and local 

DANGER

Summary of Contents for 815002013985

































Reviews: