Elsner Suntracer KNX sl Installation And Adjustment Manual Download Page 15

Page: 15 / 125

Installation and start-up

Weather Station Suntracer KNX sl

• Status: 14.07.2016 • Errors excepted. Subject to technical changes.

2.4.4. Closing the installation

2.5. Instructions for assembly and initial start-up

Remove all transport protection stickers present after installation.

The wind measurement value and thus also all wind switching outputs cannot be out-
put until 35 seconds after the power is turned on.

Fig. 14
Connect
KNX data (+|-) and
power supply (12…40V DC, 12…28V AC, 1|2)
to the connector.

The terminal assignment of the power supply
is polarity-independent.

KNX

Voltage

Fig. 15
Push the lid on the lower part. This also
makes the plug-in connection between the
board in the lid and the socket in the lower
part.

Fig. 16
Screw the lid (top) and lower part (bottom) to-
gether.

Summary of Contents for Suntracer KNX sl






























































































































Search results

Summary of Contents for Suntracer KNX sl

Reviews:

Related manuals for Suntracer KNX sl

Brands by name

Popular brands

Elsner Suntracer KNX sl, Installation And Adjustment Manual

Search results

Summary of Contents for Suntracer KNX sl

Reviews:

Related manuals for Suntracer KNX sl

Brands by name

Popular brands