ELETTROQUADRI MP3 Installation Manual Download Page 9

Page: 9 / 66

General information

© ELETTROQUADRI S.r.l.

9 / 66

INSTALLATION MANUAL

1.2.3.

General definitions

Some recurring terms in the manual are described to ensure a more complete understanding of their meaning.

ELETTROQUADRI S.r.l., the manufacturer of the aforementioned board, will be referred to as the

Manufacturer.

Danger zone:

any area inside and/or near the electric cabinet containing the board in which the presence of a person

constitutes a risk for the health and safety of said person.

Exposed person:

any person who is completely or partially inside a danger zone.

Installer:

Skilled technician for board installing/programming.

Maintenance personnel:

Person responsible for servicing and repairing the board.

REMP2 remote terminal:

External programming device which connects to the MP3 or MPCAB boards.

1.3.

Manufacturer's data

ELETTROQUADRI S.r.l.

Via Puccini, 1

21050 Bisuschio (VA) - Italy

Tel. +39 0332 470049 - Fax. + 39 0332 474032

www.elettroquadri.net

ELETTROQUADRI

SINCE 1983

MP3

Summary of Contents for MP3



































































Search results

Summary of Contents for MP3

Reviews:

Related manuals for MP3

Brands by name

Popular brands

ELETTROQUADRI MP3, Installation Manual

Search results

Summary of Contents for MP3

Reviews:

Related manuals for MP3

Brands by name

Popular brands