ELETTROQUADRI MP3 Installation Manual Download Page 11

Page: 11 / 66

Safety

© ELETTROQUADRI S.r.l.

11 / 66

INSTALLATION MANUAL

SAFETY

2.1.

Reference standards applied

REFERENCE

TITLE

EN 81-20:2014

PAR. 5.11/5.11.2.1.2/ 5.11.2.3

Safety rules for the construction and installation of lifts - Lifts for

transporting persons and property - Part 20: Lifts for persons and property

accompanied by persons

EN 81-50:2014 PAR. 5.15

Safety rules for the construction and installation of lifts - Checks and

testing - Part 50: Rules for the design, calculation, checking and testing of

lift components

UNI 10411-1:2014

Modifications to electric lifts not conforming with Directive 95/16/EC

UNI 10411-2:2014

Modifications to hydraulic lifts not conforming with Directive 95/16/EC

UNI 10411-3:2016

Modifications to electric lifts installed in conformity with Directive 95/16/

EC and UNI EN 81-1

UNI 10411-4:2016

Modifications to hydraulic lifts installed in conformity with Directive 95/16/

EC and UNI EN 81-2

UNI 10411-5:2017

Modifications to electric lifts installed in conformity with Directive 95/16/

EC or Directive 2014/33/EU and not conforming with UNI EN 81-1

UNI 10411-6:2017

Modifications to hydraulic lifts installed in conformity with Directive 95/16/

EC or Directive 2014/33/EU and not conforming with UNI EN 81-2

2.2.

Safety warnings

2.2.1.

General warnings

ATTENTION

Consequently, any intervention which alters board configuration shall automatically exonerate the

manufacturer from all liability.

Consequently, any use other than those indicated in this manual shall exonerate ELETTROQUADRI S.r.l. from all

liability for any risks which may occur.

2.2.2.

Warnings for Installer safety

Before commencing work, the Installer must be fully knowledgeable of board function, configuration, and

technical operating characteristics.

ATTENTION

Any work to be performed on the board requires maximum caution from the Installer.

IMPORTANT

Works on the board must be performed in strict observance of operational competences. The

Manufacturer declines all liability for any failure to observe said competences.

ELETTROQUADRI

SINCE 1983

MP3

Summary of Contents for MP3



































































Search results

Summary of Contents for MP3

Reviews:

Related manuals for MP3

Brands by name

Popular brands

ELETTROQUADRI MP3, Installation Manual

Search results

Summary of Contents for MP3

Reviews:

Related manuals for MP3

Brands by name

Popular brands