manualshive.com logo in svg

Electrolux 5995502399, Service Manual, Page: 134 / 173

Share
Download
Electrolux 5995502399 Service Manual Download Page 134

 6-34

Component Teardown

Compressor Area Mounting Tray

To access the compressor and inverter, condenser 
and fan assembly, or to service the sealed system, it 
may require that the compressor area mounting tray be 
removed from the bottom of the unit.   The mounting tray 
is secured with four #2 square bit screws to the bottom 
of the unit and two screws to the lower rear corners of 
the cabinet.  

 

To remove the compressor area mounting tray:

1.  Unplug unit from wall outlet.

2.  Pull unit from its installation and block unit up high 

enough to access the four bottom screws.  Have 
on hand blocks to support the mounting tray as the 
screws are removed.  Several 6 inch pieces of 2” x 
4” lumber work well.  See Caution Note.

3.  Extract the four bottom screws securing the 
 

mounting tray to the rear of the unit. 

 

(See Figure 6-95)

4.  Extract the two screws securing the mounting tray to 

the rear of the unit.

5.  Drop mounting tray down to provide better access 
 

to the grounding screws and sealed system 

 components.

 

Condenser Fan Assembly Removal

The condenser fan assembly is secured to the rear of 
the compressor area with two bolts to the compressor 
mounting plate.  The compressor area mounting tray 
does not need to be dropped to remove the fan 
assembly.

To remove the condenser fan assembly:

1.   Pull unit from its installation position and unplug from 

wall outlet.

2.  Extract the screws securing the compressor shield to 

the unit frame and remove from unit.

3.  Disconnect wire leads to condenser fan motor at 

molex connector.

4.  Extract the three bolts securing the fan assembly to 

the condenser mounting brackets.  (See Figure 6-96) 

5.  Pull fan motor assembly from unit, then pull fan 

blade from motor shaft.

 
6.  Remove the condenser fan shroud by extracting the 

two 3/8” bolts securing the shroud to the mounting 
tray.

When accessing the compressor area mounting 
tray, it is recommended to have two people to block 
the unit high enough to access the bottom screws. 

The unit is heavy, make sure unit is secure when in 
the blocked position.   The unit should not rock or 
tip when on blocks.   

If the unit should tip or fall from the blocks while 
extracting the screws, personal injury could occur 
and/or damage the unit or the customers personal 
property.

If unsure about the safety of this operation, do not 
continue.  Contact your Regional Service Quality  
Manager for assistance.

Compressor Area Mounting Tray

Bottom Screws

Ground 
Screws

Power Cord

Inverter

Screw

Screw

Figure 6-95.

Figure 6-96. 

Screws

Electrical 

Connection

Summary of Contents for 5995502399














































































































































































Reviews:

No comments