Efka AB600A5015 Operating Manual Download Page 25

Page: 25 / 64

- AB AB600A5015

Instruction Manual

- 25 -

7.8 Tape Cutter/Fast Scissors (Modes 6/7)

The signal

tape cutter/fast scissors

is issued only at the seam end. Furthermore, the manual tape cutter/fast

scissors function can be set. See also chapter "

Manual

Tape Cutter/Fast Scissors

Function

Parameters

Tape cutter

at the seam end On/Off

014

7.8.1 Tape Cutter/Fast Scissors in Mode 7

The signal

tape cutter/fast scissors

can be set separately for start and end counting. See also chapter

Manual

Tape Cutter/Fast Scissors

Function

Control

Tape cutter/

Fast

scissors

at the start of the seam On

Tape cutter/Fast scissors

at the seam end On

Tape cutter/Fast scissors

at the start and at the end of the seam On

Tape cutter/Fast scissors

at the start and at the end of the seam Off

LED-segment 3 On

LED-segment 4 On

LED-segment 3 and 4 On

LED-segment 3 and 4 Off

Key

(S3)

Output and Times for Tape Cutter

Function

Parameter

Delay time for output M1 (B3/6)

tape cutter

ON period for

output M1 (B3/6)

tape cutter

(kd1)

(kt1)

280

281



Parameter

232

must be set at "

" (tape cutter function).



The delay time for the tape cutter is usually set at "

Output and Times for Fast Scissors

Function

Parameter

Delay time for output M1 (B3/6)

fast scissors

AH1

ON period for

output M1 (B3/6)

fast scissors

AH1

Delay time for output M2 (B3/7)

fast scissors

AH2

ON period for output M2 (B3/7)

fast scissors

AH2

(kd1)

(kt1)

(kd2)

(kt2)

280

281

282

283



Parameter

232

must be set at "

" (fast scissors function).



The delay times for "fast scissors" are usually set at "

7.9 Manual Tape Cutter/Fast Scissors

Upon pressing an external key depending on the pre-selection of parameters

240...246

, the

tape cutter

fast

scissors

can be enabled anywhere in the seam or at standstill.

See also chapter "Connection Diagram" in the List of Parameters!

7.10 Seam with Stitch Counting

Function

Parameters

Stitch counting On/Off

(n7)

015

7.10.1 Number of Stitches for a Seam with Stitch Counting

Function

Parameters

Number of stitches for the seam with stitch counting

(Stc)

007

The number of stitches for stitch counting can be set directly on the control with parameter

007

Summary of Contents for AB600A5015

































































Search results

Summary of Contents for AB600A5015

Reviews:

Related manuals for AB600A5015

Brands by name

Popular brands

Efka AB600A5015, Operating Manual

Search results

Summary of Contents for AB600A5015

Reviews:

Related manuals for AB600A5015

Brands by name

Popular brands