manualshive.com logo in svg

EFD Ultra 325TT, User Manual, Page: 63 / 79

Share
Download
EFD Ultra 325TT User Manual Download Page 63

®

A NORDSON COMPANY

Ultra TT User's Guide

Version 1.2

63

Symptom

Possible Cause

Recovery Procedures

1. System is not connected to

Check the Main Air Inlet at the rear

facility air supply.

of the system.

2. Main Air Regulator is OFF.

Verify Main Air Regulator is set
properly.

3. Unit has homed at start-up.

“Home” the machine to energize 
Main Air Solenoid. If PDA is 
attached, exit the EFD software 
program. The machine will home 
when you enter the EFD software 
program again. Alternatively, home 
the machine from the front panel by 

pressing the soft key corresponding
to Jog, then press Home.

Factory air supply fluctuates air  

Install EFD #2000F755TT Filter 

compressor ON/OFF.

Regulator and set pressure to 70 psi.

There is no air pressure.

Make sure the Fluid Pressure 
Regulator is set to the proper air 
pressure.

1. Main Air Switch OFF.

Make sure Main Air Switch is ON.

2. Air pressure

Make sure the Fluid Pressure 
Regulator is set to the proper air 
pressure.

3. Syringe Barrel Adapter is

Check the connection at the top of 

disconnected.

the Z-head to make sure that it is 
installed properly and at the correct 
location.

4. Incorrect setup in PDA software.

Check valve setup to ensure that
the correct valve and options are 
selected.

Damaged Regulator.

Contact your EFD Ultra TT 
representative for a replacement.

This is a normal function of the

Replace P1 if hissing.

30 psi bleed-type regulator (P2).
P1 is a non-bleed regulator and
should not hiss.

Table 11.2: Pneumatic Troubleshooting

No fluid pressure

No valve or syringe
barrel pressure

Leaky Regulator

Air Regulator is hissing

No air pressure

Unstable air pressure

Summary of Contents for Ultra 325TT
















































































Reviews:

No comments