manualshive.com logo in svg

EFD Ultra 325TT, User Manual, Page: 61 / 79

Share
Download
EFD Ultra 325TT User Manual Download Page 61

®

A NORDSON COMPANY

Ultra TT User's Guide

Version 1.2

10.3

SPARE PARTS LIST

The items below are the recommended spare parts for the Ultra TT System. Items marked * are
only relevant for those customers using laser or I/O’s respectively.

61

Part Number

Description

Quantity

Comments

Recommended

7001PM-KIT

TT Grease Maintenance Kit

1

700847

Switch, Start, Round

1

700848

Switch, E-Stop

1

700822

PWA Servo Amp

1

700820-3*

Laser Module 5V

1

optional

700824

PWA Front Panel

1

700825

Battery, nonvolatile

1

700826

Sensor Optointerrupter

1

2002F

Regulator, 30 psi

1

2001C

Gauge, 0-100 psi

1

700827

Assembly, Height Sensor

1

700828

Plug-M 14S Screw Phoenix 3.81 mm

1

700829

Plug-M 7S Screw Phoenix 5.08 mm

1

700830

Plug-M 4X Screw Phoenix 5.08 mm

1

700831*

Cable, GP Outputs

1

optional

700832*

Cable, GP Inputs

1

optional

700833*

Cable, Interlock Extender

1

optional

700834

Interlock Faker

1

700818

Cable, PDA RS232 & Power

1

700835

PWA programmed, main

1

700836

Motor Assembly, DC 190 oz-in

1

2001A

Gauge, EFD 0-30 psi

1

2002

Regulator, 100 psi

1

700837

Probe, 1.9 x 250 HS

1

700838

Power Supply 320W, 48VDC, UNIV

1

700839

Power Supply 100W, 24VDC, UNIV

1

10.4

DISPOSAL

This equipment is regulated by the European Union under WEEE Directive (2002/96/EC).
See 

www.nordson.com

for information about how to properly dispose of this equipment.

All other customers:
Please contact EFD Customer Service at 800-556-3484 or 

[email protected]

for a RMA number

before shipping the unit back to EFD for safe disposal.

Summary of Contents for Ultra 325TT
















































































Reviews:

No comments