background image

Eclipse RatioMatic Burners, RM Series, V5, Installation Guide 110, 12/3/2014

6

In this section you will find information and instructions
needed to install the burner and system components.

Handling & Storage

Handling

• Make sure that the area is clean.
• Protect all components from weather, damage, dirt 

and moisture.

• Protect the components from excessive 

temperatures and humidity.

• Take care not to drop or damage components.

Storage

• Make sure the components are clean and free of 

damage.

• Store the components in a cool, clean, dry room.
• After you have made sure everything is present and 

in good condition, keep the components in their 

original packaging as long as possible

Approval of Components

Limit Controls & Safety Equipment

All limit controls and safety equipment must comply with

all applicable local codes and/or standards and must be
listed for combustion safety by an independent testing
agency. Typical application examples include:

• American: NFPA 86 with listing marks from UL, FM, 

CSA

•  European: EN 746-2 with CE mark from TuV, 

Gastec, Advantica

Electrical Wiring

All the electrical wiring must comply with all applicable

local codes and/or standards such as:

•  NFPA Standard 70
• IEC60364
• CSA C22
• BS7671

Gas Piping

All the gas piping must comply with all applicable local

codes and/or standards such as:

•  NFPA Standard 54
• ANSI Z223
• EN 746-2

Where to Get the Standards:

The NFPA Standards are available from: 
National Fire Protection Agency 
Batterymarch Park
Quincy, MA 02269
www.nfpa.org

The ANSI Standards are available from: 

American National Standard Institute 

1430 Broadway
New York, NY 10018
www.ansi.org

The UL Standards are available from: 
333 Pfingsten Road
Northbrook, IL 60062
www.ul.com

The FM Standards are available from: 
1151 Boston-Providence Turnpike
PO Box 9102
Norwood, MA 02062
www.fmglobal.com/approvals

Information on the EN standards and where to get them is
available from: 
Comité Européen de Normalisation 

Stassartstraat 36

B-1050 Brussels
Phone: +32-25196811

Fax: +32-25196819

www.cen.eu

Comité Européen de Normalisation Electronique 

Stassartstraat 36

B-1050 Brussels
Phone: +32-25196871

Fax: +32-25196919 

www.cenelec.org

Installation

3

Summary of Contents for RatioMatic RM Series
























Reviews: