background image

Riello Burner

Installation and Operating
Instruction Supplement

Use in conjunction with the original technical literature supplied by Riello

Riello Burner

Gas or Oil-Fired Burner
for use with Vitola 200 boiler

Heating input

83 to 300 MBH
24 to

88 kW

Read and save these instructions
for future reference.

IMPORTANT

If the information in this manual is not followed
exactly, a fire or explosion may result causing
property damage, personal injury or loss of life.

WARNING

Improper installation, adjustment, and/or
operation could cause carbon monoxide
poisoning resulting in injury or loss of life.

This product must be installed and serviced by a
professional service technician who is
experienced and qualified in hot water boiler
installation and gas combustion.

WARNING

Do not store or use gasoline or other flammable
liquids in the vicinity of this or any other
appliance.

WHAT TO DO IF YOU SMELL GAS

Do not try to light any appliances.

Do not touch any electrical switches, do not
use any phone in your building.

Immediately call your gas supplier from a
neighbor’s phone. Follow the gas supplier’s
instructions.

If you cannot reach your gas supplier, call the
fire department.

Installation and service must be performed by a
qualified installer, service agency or the gas
supplier.

5265 665 v2.5 12/2009

Summary of Contents for Riello

























Reviews: