EASYPRINT Compact 32D Product Manual Download Page 70

Page: 70 / 243

DESCRIPTION AND INSTALLATION

2-50

25364 Issue 8 March 2018

Communicator II Ribbon Threading Procedure

Capstan

Rewind
Spindle

Ribbon Guide

Roller

Unwind
Spindle

Dancing

Arm

Dancing

Arm

Cassette Unit showing Ribbon Path Label

(Right-Hand Cassette Shown)

Ribbon Guide

Roller

Ribbon Path label

(1) If fitting a replacement ribbon, remove the used roll and discard,

re-use the inner core if needed.

(2) Fit the new ribbon roll on the unwind spindle and the inner core to the

rewind spindle.

(3) Thread the ribbon as shown on the ribbon path label fitted to the

cassette assembly. (See overleaf).

(4) Wrap the ribbon around the empty ribbon core several times, taking

up any slack in the ribbon path to complete the operation.

Ribbon Path

Ribbon Path Diagram

Summary of Contents for Compact 32D




















































































































































































































































Search results

Summary of Contents for Compact 32D

Reviews:

EASYPRINT Compact 32D, Product Manual, Page: 70 / 243

Search results

Summary of Contents for Compact 32D

Reviews: