Dynapac CA270 Instruction Manual Download Page 49

Page: 49 / 99

Operation

ICA270-IN2EN1.pdf

2012-11-05

Switching off

Fig. Instrument panel
1. Starter switch
9. Instrument guard
22. Panel for warning lamps

Check instruments and warning lamps to see if any
faults are indicated. Switch off all lights and other
electrical functions.

Turn the starter switch (1) to the left to switched off
position 1. At the end of the shift, lower the instrument
cover (22) and lock it.

Parking

Master switch

Fig. Engine compartment
1. Master switch

Before leaving the roller for the day, switch the master
switch (1) to the disconnected position and remove the
key.

This will prevent battery discharging and will also
make it difficult for unauthorized persons to start and
operate the machine. Also lock the engine hood.

Summary of Contents for CA270




































































































Search results

Summary of Contents for CA270

Reviews:

Related manuals for CA270

Brands by name

Popular brands

Dynapac CA270, Instruction Manual

Search results

Summary of Contents for CA270

Reviews:

Related manuals for CA270

Brands by name

Popular brands