Dynajet 350 me Page 76 Operating Instruction Download

Page: 76 / 96

Faults, Cause and Remedy

7 — 2

06_0006_0604GB

The following section provides a description of possible causes of
faults and their remedies.

The operating pressure fluctuates

Cause

Remedy

The water filter is contami-
nated.

Clean or replace the water filter.

The fan jet nozzle is blocked or
worn.

Clean or replace the fan jet nozzle.

The operating pressure is too low

Cause

Remedy

The fan jet nozzle is too large.

Use a smaller fan jet nozzle.

The seal on the water pump is
worn.

Replace the pump seal.

The pump valves are dirty or
have seized.

Consult the Putzmeister Mörtelmaschine GmbH After Sales de-
partment.

The operating pressure is too high (pressure limiting valve or unloader is activated)

Cause

Remedy

The fan jet nozzle is too small.

Use a larger fan jet nozzle.

The fan jet nozzle is dirty.

Clean the fan jet nozzle.

7.1

Machine, general

Summary of Contents for 350 me

































































































Search results

Summary of Contents for 350 me

Reviews:

Related manuals for 350 me

Brands by name

Popular brands

Dynajet 350 me, Operating Instruction

Search results

Summary of Contents for 350 me

Reviews:

Related manuals for 350 me

Brands by name

Popular brands