Dynajet 350 me Operating Instruction Download | Manualshive

Page: 50 / 96

background image

Transport, Set-up and Connection

4 — 2

04_0007_0508GB

The machine does not have any attachment points and should there-
fore loaded onto a suitable transport aid (euro pallet). Use a suitable
crane with lifting gear or a fork-lift truck to lift the machine.

Danger of crushing

Lift the machine carefully with a fork-lift truck and move with great
care.

When lifting with the crane, determine the centre of gravity of the ma-
chine by lifting carefully. All cables or chains on the lifting gear must
be tensioned evenly and the machine must be raised evenly at all
support points.

Suspended Load

Ensure no persons are under a suspended load.

4.2

Transporting the
machine

«
...
48
49
50
51
52
...
»

Summary of Contents for 350 me

































































































Reviews:

No comments

Related manuals for 350 me

Brand: SIP Pages: 16

Brand: Kränzle Pages: 29

Brand: Champion Pages: 33

Brand: AT-OS Pages: 60

Brand: Maytag Pages: 36

ULTIMATE 617 LE

Brand: Garland Pages: 100

Brand: Hotpoint Pages: 16

Brand: Samsung Pages: 48

Brand: Panasonic Pages: 50

Brand: Candy Pages: 53

Brand: AEG Pages: 48

Brand: AEG Pages: 23

Brand: AEG Pages: 44

Brand: AEG Pages: 52

Brand: AEG Pages: 64

Brand: AEG Pages: 40

Brand: AEG Pages: 44

Brand: AEG Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands