DXV AT100 Installation & User Manual Download

Page: 7 / 48

Using T

his Pr

oduct

Ins
talling T

his Pr

oduct

Remove the parts from the box and make sure all the parts in the parts list (below) are

present. Inspect the parts carefully to make sure they are in good condition.

If any part is damaged or missing, do not install this product. Contact the nearest customer

service representative for the part(s) you need.

The following parts are included:

•

Seat unit (with heated toilet seat, toilet seat lid and power cord)

•

Mounting plate

•

Manual set

•

Mounting bolts, washers, and bushings (2 pieces each)

•

Junction fitting (with a packing)

•

Seat unit water supply hose (with 2 clips)

•

Remote control

•

Bracket

•

Batteries

•

Wood screw

•

Plastic anchors

3. Installing This Product

Installation Requirements

Before installing this product, ensure that each of the following installation

requirements are met.

Contents

Seat unit

Packing

2 mm (0.08")

thick

Junction fitting

Manual set

Clip

Water supply

hose

(37.40'' (950 mm) long)

Mounting bolt

Bushing

Mounting plate

(This plate attaches to the seat unit.)

Washer

Batteries (2) Wood screws

Plastic anchors

Bracket

Remote control unit

*Remote control unit and bracket are

packed in the box.

For remote control unit

Summary of Contents for AT100

















































Search results

Summary of Contents for AT100

Reviews:

Related manuals for AT100

Brands by name

Popular brands

DXV AT100, Installation & User Manual

Search results

Summary of Contents for AT100

Reviews:

Related manuals for AT100

Brands by name

Popular brands