background image

     Roverpet

 20 Kiji Dava Circle   Prescott, Arizona  86301   

800-658-5925

   

[email protected]

 

 

 

Roverpet #KK3 Cat Climber Assembly Instructions   

   

     

 

 

  

          

            

 
 
 
 
 
 
 
 
 
 

 
 
 
Roverpet #KK3 Climber Inventory:

 

(4)  

#24TLC legs  

(4)    #18TAC arms         (4)      #34URP short uprights 

(4)   

#46URP long uprights 

 

 

(10) 

#17CBC crossbars 

(17” long) 

(10)   #23CBC crossbars 

(23” long) 

(10)   #250 divider clips  
(6) 

# FDC 

“custom” wall clips with screws 

(5)  

Sheep skin furry pads 

(3)  

#CSR12 cat scratch rollers 

 

1.) Unpack shipping carton and inspect quantity of components against 

inventory list above. 

2.) As assembly will be accomplished by first building two separate towers 

and then attaching them together, gather the parts needed to assemble 
the two-level tower first as follows: 
 
(2) #24TLC legs, (2) #18TAC arms, (4) #34URP short uprights,  
(4) #17CBC crossbars, (4) #23CBC crossbars, (2) sheepskin pads 
 

3.) Connect two #24TLC legs together by inserting two #17CBC crossbars 

into the holes between them as seen in the photo below. 
 
 
 
 
 
 
 

Summary of Contents for KK3







Reviews: