Roverpet KK3 Assembly Instructions Manual Download Page 5

     Roverpet

 20 Kiji Dava Circle   Prescott, Arizona  86301   

800-658-5925

   

[email protected]

 

 

 
20.) Install the rings of the last remaining sheepskin pad, furry side up, over   

the uprights and down onto the crossbars just installed. See the right 

       photo above. 
21.) Install the last two remaining #23CBC crossbars into the highest set of  
       holes in the uprights to span across the longest faces of the assembly.    
       See the left photo below. 
 
 
 
 
 
 
 
 
 
 
 
22.) Install the two #18TAC arms into the uprights and fully seat them. See    
       the right photo above. 
23.) Set the two completed assemblies side-by-side and connect them     
       together by attaching the supplied #250 clips along the length of the  
       center frame pipes. Place five clips on the front and five on the rear of the  
       assembly. See the photos below. 
 
 
 
 
 
 
 
 
 
 
24.) Attach the six supplied #FDC wall clips to the rear of the assembly as    
      show in the photos below. 
 
  
 

 

 
 

  

 

 
 

 

      
      25.) Select a wall location for the Roverpet #KK3 Cat Climber and attach it to 
the wall with anchors (not supplied by Roverpet) which are appropriate for the  
             construction material of the wall. As an example, typical stud and drywall       

Attach five 

#250 clips 

on both the 

front and 

back of the 

assembly at 

these 

locations. 

Attach FDC 

wall clips 

on backside 

of assembly 

at these 

locations. 

Summary of Contents for KK3







Reviews: