DXV AT100 Installation & User Manual Download Page 13

Page: 13 / 48

Using T

his Pr

oduct

Ins
talling T

his Pr

oduct

Water supply connection socket

Protective cover

Water supply

socket

O-ring

Water supply

hose for the seat

Clip

Bend here

Water supply

socket

Clip

O-ring

Installation diagram

Water supply hose for bidetet

Flathead

screwdriver

3. Installation of water supply hose to the bidet

1) Remove the protective cover

from the end of the water

supply hose, and pull out the

cap from the water supply

connection socket.

2) Connect the water supply

hose for the bidet to the

water supply connection

socket.

3) Insert the attachment clip onto

the water supply hose to attach

it to the bidet and water supply

connection socket.

* The attachment clip can be attached

in any direction.

CAUTION

• Firmly insert the clip.

* If the clip is not firmly inserted,

it may cause water leaks.

4) Bend the clip end and firmly

clip together both the feeding

hose for the bidet and the

feeding socket. After you

install the clip, twist it in both

directions to verify that it is

firmly attached.

CAUTION

•

Be careful not to damage the O-ring.

* A damaged O-ring may cause water to leak.

CAUTION

• Insert the clip until

you feel the clip edge

click.

* If not firmly inserted, it

may cause water leaks.

•

When removing the clip, hold

the clip with your fingers, and

using a flathead screwdriver,

push the clip downward to

remove it as shown in the

figure below.

Water supply connection socket

Protective cover

Water supply

socket

O-ring

Water supply

hose for the seat

Clip

Bend here

Water supply

socket

Clip

O-ring

Installation diagram

Water supply hose for bidetet

Flathead

screwdriver

Water supply connection socket

Protective cover

Water supply

socket

O-ring

Water supply

hose for the seat

Clip

Bend here

Water supply

socket

Clip

O-ring

Installation diagram

Water supply hose for bidetet

Flathead

screwdriver

Water supply connection socket

Protective cover

Water supply

socket

O-ring

Water supply

hose for the seat

Clip

Bend here

Water supply

socket

Clip

O-ring

Installation diagram

Water supply hose for bidetet

Flathead

screwdriver

Summary of Contents for AT100

















































Search results

Summary of Contents for AT100

Reviews:

Related manuals for AT100

Brands by name

Popular brands

DXV AT100, Installation & User Manual

Search results

Summary of Contents for AT100

Reviews:

Related manuals for AT100

Brands by name

Popular brands