manualshive.com logo in svg

Durr Dental Vector Scaler, Installation And Operating Instructions Manual

Share
Download
Durr Dental Vector Scaler Installation And Operating Instructions Manual Download Page 20

18 

9000-615-32/02  1808V002 

Usage

9.4  Flexible foot switch

The handpieces are operated with the flexible 
foot switch

In wireless operation the flexible foot switch is 
supplied with voltage from a battery If the bat-
tery power starts to fail, the orange PEDAL LED 
on the unit lights up

Interference can occur in wireless opera-
tion if the battery power is low, so it is im-
portant to change the batteries in good 
time

The service life of the batteries is around 1 year 
or approx 900 treatments
If the battery is empty or not present then the 
flexible foot switch can be connected with a ca-
ble to the unit so that the treatment can be con-
tinued The battery can then be inserted later on
Changing the battery – "154 Inserting or chang-
ing the battery in the flexible foot switch"

9.5  Fluid container

The fluid container can hold up to approx 
600 ml of water or water-based fluids

9.3  Steri-box

Scaler steri-box

 (cover: blue)

All parts which can be sterilised are optimally 
stored in the special Vector Scaler steri-box
For steam sterilisation the steri-boxes are 
placed in the small steam steriliser, see "13 Re-
processing" on page 29
If sterile storage is required, wrap the steri-box 
in suitable sterilisation packaging in accordance 
with DIN11607-1 and seal

The rubber clips on the carrier plate can be re-
placed if necessary

EN

Summary of Contents for Vector Scaler

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands