manualshive.com logo in svg

Durr Dental Vector Scaler, Installation And Operating Instructions Manual

Share
Download
Durr Dental Vector Scaler Installation And Operating Instructions Manual Download Page 42

40 

9000-615-32/02  1808V002 

Usage

 

i

Take out the battery from the holder and dis-
pose of it in an environmentally friendly way

Inserting the battery:

 

i

Insert the battery in the holder Make sure that 
the battery is inserted with the correct polarity

Closing the cover:

 

i

Make sure that the two pedal return springs 
are present and correctly positioned If they 
are not, the function of the unit may be im-
paired

 

i

Fit the cover in such a way that the two pins 
on the side of the flexible foot switch snap into 
the holes in the cover

15.4 Inserting or changing the  

battery in the flexible foot 
switch

A new battery should be inserted in the flexible 
foot switch prior to initial start-up in wireless op-
eration or if the power of the existing battery is 
low

Opening the cover:

 

i

Press both pins on the flexible foot switch to-
gether at the same time and lift the cover off

Checking the battery:

 

i

Press the button to the left of the battery 
Green LED lights up: battery power is OK
Green LED does not light up: change the 
battery

Taking out the battery:

The old battery must be properly dis-
posed of in accordance with applicable 
national and regional guidelines for envi-
ronmentally friendly disposal Do not 
throw batteries away with domestic 
waste

EN

Summary of Contents for Vector Scaler

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands