Entering the code:
each time you press the button (2) the displayed
number increases from “0” to “9” and then returns
to “0”; to confirm the number, press the reset button
(4). Repeat the procedure until inserting the fourth
digit. Press the reset button (4) again to confirm.
If the code is incorrect (A), the instrument panel will
return to the initial indication in order to enter the
code again.
Note
There is no limit to the number of times the
code can be reentered; the instrument panel will turn
off automatically 120 seconds after an attempt to
enter the code.
If the code was entered correctly (B), the message
"PIN OK" will flash on the display for 4 seconds.
After 4 seconds, the instrument panel will return to
the "normal" view (with all indications active).
From this moment, the vehicle can be started using
the start button (Key-On).
Note
The vehicle can be started until a Key-Off is
performed; if the problem still persists upon the next
starting attempt, repeat the procedure from the
beginning in order to start the motorcycle
"temporarily".
Important
If this procedure is necessary in order to start
the vehicle, contact an Authorized Ducati Service
Center as soon as possible to fix the problem.
174
Summary of Contents for Multistrada 1200S Pikes Peak
