The relation of the DTC intervention level to the circuit
characteristics:
If all the corners on the track/circuit can be taken at a
similar speed, it will be easier to find an intervention
level that is satisfactory for every bend; on the other
hand, if the track has, for example, one corner that is
much slower than all the others, it will be necessary
to find a compromise level (on the slow corner the
DTC will tend to control more than on the faster
corners).
The relation of the DTC intervention level to riding
mode:
The DTC will tend to kick in more with a “smooth”
riding mode, where the bike is leaned over further,
rather than with a “rough” style, where the bike is
straightened up as quickly as possible when exiting a
turn.
Tips for use on the track
We recommend that level 6 be used for a couple of
full laps (to allow the tires to warm up) in order to get
used to the system. Then try levels 5, 4, etc., in
succession until you identify the DTC sensitivity level
that suits you best (always try each level for at least
two laps to allow the tires to warm up).
Once you have found a satisfactory setting for all the
corners except one or two slow ones, where the
system tends to kick in and control too much, you can
try to modify your riding style slightly to a “rougher”
approach to cornering i.e. straighten up more rapidly
on exiting the corner, instead of immediately trying a
different level setting.
Tips for use on the road
Activate the DTC, select the URBAN Riding Mode
(preset DTC level 6) and ride the motorcycle in your
usual style; if the level of DTC sensitivity seems
excessive, try swapping to TOURING Riding Mode
(preset DTC level 5), if you still feel the system is too
much sensitive try the SPORT Riding Mode (preset
DTC level 4). If no Riding Mode meets your
requirements, you can still customize the settings
following the instructions in the table above until you
find the level that best suits your riding style.
If changes occur in the grip conditions and/or circuit
characteristics and/or your riding style, and the level
setting is no longer suitable, switch to the next level
up or down and proceed to determine the best
setting (e.g. if with level 7 the DTC intervention
seems excessive, switch to level 6; alternatively, if on
98
Summary of Contents for Multistrada 1200S Pikes Peak
