manualshive.com logo in svg

DSC Power832, Installation Manual, Page: 4 / 48

Share
Download
DSC Power832 Installation Manual Download Page 4

S Y S T E M  I N T R O D U C T I O N

4

1.2.8

PC5400 Printer Module

This PC5400 Printer Module will allow the panel to print out all events that
occur on the system to any serial printer. All events will be printed with
the Partition, time, date and the event that occurred 

(See S

ection 5.29

“On-site Printer”

).

1.2.9

LINKS1000 Cellular Communicator 

(This device is not UL Listed)

The LINKS1000 Cellular Communicator provides an efficient, cost-effective
method for adding cellular back up. The unit comes in its own cabinet with
antenna and requires a separate battery and transformer 

(See 

Section 5.26

“LINKS1000 cellular communicator”

).

1.2.10

Cabinets

Several different cabinets are available for the PC5010 modules. They are as follows:

PC5003C 

Main Control Cabinet for the PC5010 main panel. Dimensions 288mm x 298mm x 78mm /

11.3” x 11.7” x 3” approximately.

PC5002C

 Cabinet to house the PC5204 Power Supply Output Module. Dimensions 213mm x 235mm x

78mm / 8.4” x 9.25” x 3” approximately.

PC5004C

  Cabinet to house the Escort5580 Module and PC5400 Printer Module. Dimensions 229mm x

178mm x 65mm / 9” x 7” x 2.6” approximately.

PC5001C

  Cabinet to house the PC5108 Zone Expander Module and the PC5208 Eight Low Current

Output Module. Dimensions 153mm x 122mm x 38mm / 6” x 4.8” x 1.5” approximately.

PC5001CP

  Plastic Cabinet to house the PC5108 Zone Expander Module and the PC5208 Eight Low

Current Output Module. Dimensions 146mm x 105mm x 25.5mm / 5.75” x 4.2” x 1” approximately.

1.2.11

Backplates

There are two different backplates available for keypads to locate an Audio Station next to the keypad:

PC55BP1 Backplate

This backplate is to be used when an Audio Station is to be located next to
a keypad. Dimensions 208mm x 115mm x 18mm  / 8.2” x 4.5” x 0.25”
approximately.

PC55BP2 Backplate

This backplate is to be used when an Audio Station is to be located next to a
keypad. In addition the backplate will allow you to mount a PC5108 Zone
Expander Module or the PC5208 Eight Low Current Output Module. Dimensions
208mm x 115mm x 18mm  / 8.2” x 4.5” x 0.7” approximately.

1.3

Out of the Box

You should find the following equipment included in your system. Verify each of the components is included:
• one PC5010 main control cabinet
• one PC5010 main control circuit board
• one PC55XX (8 zone, 16 zone or 32 zone LED) / LCD5500 keypad
• one Installation Manual
• one Programming Worksheet Manual
• one Instruction Manual (LED or LCD keypad)
• one hardware pack consisting of:

- five plastic circuit board standoffs

- sixteen 5600 ohm (5.6K) resistors

- seventeen 2200 ohm (2.2K) resistors

- one 1000 ohm (1K) resistor

Summary of Contents for Power832

















































Reviews:

No comments