manualshive.com logo in svg

DSC Power832, Installation Manual, Page: 29 / 48

Share
Download
DSC Power832 Installation Manual Download Page 29

P R O G R A M  D E S C R I P T I O N S

29

5.7.6

Priority/Emergency

The panel will transmit a 

Keypad Fire Alarm 

Reporting Code AND the 

Keypad Fire Restoral 

Reporting

Code when the Fire Keys on any keypad is pressed for two seconds.
The panel will transmit a 

Keypad Auxiliary Alarm 

Reporting Code AND the 

Keypad Auxiliary Restoral

Reporting Code when the Auxiliary Keys on any keypad is pressed for two seconds.
The panel will transmit a 

Keypad Panic Alarm 

Reporting Code AND the 

Keypad Panic Restoral

Reporting Code when the Panic Keys on any keypad is pressed for two seconds.
The panel will transmit a 

Duress 

Reporting Code any time either Duress Code is entered at any keypad. If

the panel is armed using the Duress Code the panel will also transmit a 

Closing by Duress 

Reporting

Code or if the panel is disarmed it will also transmit an 

Opening by Duress 

Reporting Code.

If PGM2 is being used for two wire smoke detectors 

(See 

Section 5.10 “PGM Outputs”

) the panel will send

a 

Two Wire Smoke Alarm 

Reporting Code if a smoke detector goes into alarm. The panel will transmit the

Two Wire Smoke Alarm Restoral 

Reporting Code when the zone is restored.

5.7.7

Maintenance

The panel will transmit a 

Battery Trouble Alarm 

Reporting Code when the backup battery drops below

11.5 V

DC

. The 

Battery Trouble Restoral 

Reporting Code will not be transmitted until the battery has been

charged over 12.5 V

DC

.

To prevent the panel from transmitting an 

AC Failure Trouble Alarm 

Reporting Code during short power

outages the panel will not send the signal unless AC power is lost for the amount of minutes programmed
for the AC Failure Communication Delay. The 

AC Failure Trouble Restoral 

Reporting Code will be

transmitted as soon as AC power is restored.

NOTE: If AC failure communications delay is programmed as 000, AC failure transmission will be
disabled.

A 

Bell Circuit Trouble Alarm 

Reporting Code will be transmitted immediately if an open condition is

measured on the Bell Output of the main panel. The 

Bell Circuit Trouble Restoral 

Reporting Code will be

transmitted as soon as the problem is corrected.
A 

Fire Trouble Alarm 

Reporting Code will be transmitted immediately when an open condition is

measured on any Fire type zone 

(See 

Section 5.1 “Zone Definitions”

). The 

Fire Trouble Restoral 

Reporting

Code will be transmitted as soon as the problem is corrected.
The 

Auxiliary Power Supply Trouble Alarm 

Reporting Code will be transmitted if the AUX output is

shorted. The AUX output control incorporates a fuseless design. When excessive current is drawn the
panel will automatically shut off the output. The panel will constantly check the AUX output and when the
excessive current draw is removed the panel will reset the output and transmit an 

Auxiliary Power Supply

Trouble Restoral 

Reporting Code.

A 

TLM Trouble 

Reporting Code can only be transmitted if a LINKS1000 Cellular Communicator is being

used 

(See 

Section 5.26 “LINKS1000 Cellular Communicator”

). The panel will only transmit the signal after

the time programmed for the TLM Trouble Delay. The 

TLM Restoral 

Reporting Code will be transmitted

within 10 seconds of the problem being corrected.
A 

General System Trouble 

Reporting Code will be transmitted if the panel detects any of the following on

the PC5204 Power Supply/Output Module: AC Power Failure, Low Battery, AUX Output Trouble, Output #1
Supervisory trouble or the PC5400 is off-line. The 

General System Trouble Restoral 

Reporting Code will

be transmitted when all of the listed problems are corrected.
A 

General System Supervisory Trouble 

Reporting Code will be transmitted if any module goes missing

from the Keybus. If the module is a zone expander the panel will also transmit the 

Zone Expander

Supervisory Alarm Trouble 

Reporting Code. The panel will send a 

General System Supervisory

Restoral 

Reporting Code when the problem is corrected as well as a 

Zone Expander Supervisory

Restoral 

Reporting Code if the module is a zone expander.

5.7.8

Test Transmissions

The panel can be programmed to transmit a 

Periodic Test Transmission

     Reporting Code (See 

Section

5.13 “Test Transmissions”

), a 

System Test 

Reporting Code 

(See 

Section 3.4 “[

✱

] Commands, [

✱

] [6]”

) or a

LINKS1000 Test Transmission 

Reporting Code 

(See 

Section 5.26 “LINKS1000 Cellular Communicator”

).

5.7.9

Wireless Maintenance

The panel will transmit a 

General Zone Low Battery Alarm 

Reporting Code if a low battery condition is

indicated by a detector. The transmission of the trouble will be delayed by the number of days
programmed for 

Zone Low Battery Transmission Delay

. The 

General Zone Low Battery Restoral

Reporting Code will be transmitted when the problem is corrected. The specific zone that caused the
trouble will be stored to the Event Buffer.

The restoral will not be transmitted until all detectors indicate a good battery condition.

Summary of Contents for Power832

















































Reviews:

No comments