manualshive.com logo in svg

DSC Power832, Installation Manual, Page: 2 / 48

Share
Download
DSC Power832 Installation Manual Download Page 2

S Y S T E M  I N T R O D U C T I O N

2

False Alarm Prevention Features

• Audible Exit Delay

• Audible Exit Fault

• Urgency on Entry Delay

• Quick Exit

• Swinger Shutdown

• Recent Closing Transmission

• Communication Delay

Additional Features

• Auto Arm by Partition at Specified Time
• Keypad Activated Alarm Output and Communicator Test
• Keypad Lockout
• Audio Capability using the PC5928 Audio Interface Module which allows local intercom and Central

Station 2-Way Listen in.

• All modules connect to the system via a four wire Keybus up to 1000’/330m from main panel
• Event Buffer can be printed using PC5400 RS232 Serial Interface module
• Zone Doubler Option
• Supports the Escort5580 Voice Prompt Module with Automation/Lighting Control
• 128 Event Buffer, Time and Date Stamped
• Upload/Download Capability

1.2

Additional Devices

1.2.1

Keypads

A maximum of eight (8) keypads can be connected to the control panel and can be any combination of the
following listed. Different keypads (with function keys) can be used for different size systems; 8 zone, 16
zone and 32 zone.

PC5508/KP5508

PC5516/KP5516

PC5532/KP5532

LCD5500/KPL5500

8 zone LED keypad

16 zone LED keypad

32 zone LED keypad

LCD keypad

1.2.2

PC5108 Eight Zone Expander Module

Eight zone expander module can be used to increase the number of zones on
the system. Up to 3 modules can be connected to increase the system zones to
a maximum of 32. 

(See PC5108 Installation Instructions Sheet.)

1.2.3

PC5132 Wireless Receiver Module

The PC5132 Wireless Receiver module can be used to connect up to 32
wireless devices. All devices are spread spectrum, 900 MHz, fully supervised
and use standard ‘AAA’ or ‘AA’ alkaline batteries 

(See 

Section 5.27 “Wireless

Expansion”

). (See PC5132 Installation Manual.)

Additional wireless devices are available:

WLS904

WLS906

WLS907

WLS908

WLS909

WLS910

WLS904 Wireless Motion Detector

The wireless Motion Detector can be used in conjunction with the PC5132 Wireless Receiver to include
wireless space protection. The unit comes with four ‘AAA’ batteries

.

WLS906 Wireless Smoke Detector

The wireless Smoke Detector can be used in conjunction with the PC5132 Wireless Receiver to include
wireless smoke detection. The unit comes with six ‘AA’ batteries

.

Summary of Contents for Power832

















































Reviews:

No comments