DSC Power832 Installation Manual Download Page 10 | Manualshive

Page: 10 / 48

DSC Power832 Installation Manual Download Page 10

G E T T I N G S T A R T E D

10

2.9

Zone Wiring

There are several different ways in which zones may be wired, depending on the programming options
selected.

Any zone defined as Fire, 24 Hour Links Supervisory and Links Answer (See Section 5.1
“Zone Definitions”) will automatically require a single End of Line (EOL) resistor regardless
of which type of zone wiring supervision is selected

.....

When reconfiguring the zone supervision from a non-default setting, such as DEOL to EOL/
NC to DEOL/disabling zones 1-8 while open or in trouble, the system should be powered
down completely and powered up again.

2.9.1

Normally Closed (NC) Loops

Wire all zones according to the following diagrams:

2 NORMALLY CLOSED

CONTACTS WITH

NO END OF LINE

RESISTOR

ANY Z

TERMINAL

ANY COM

TERMINAL

NORMALLY CLOSED

CONTACT;

NO END OF LINE

RESISTOR

ANY Z

TERMINAL

ANY COM

TERMINAL

This option can only be selected if Normally Closed (NC) detection devices or contacts are
being used

.....

2.9.2

Single End Of Line (EOL) Resistors

Wire all zones according to the following diagrams:

NORMALLY CLOSED

CONTACT WITH

5600

Ω

END OF LINE

RESISTOR

ANY Z

TERMINAL

ANY COM

TERMINAL

NORMALLY OPEN

CONTACTS WITH

5600

Ω

END OF LINE

RESISTOR

ANY Z

TERMINAL

ANY COM

TERMINAL

ANY Z

TERMINAL

ANY COM

TERMINAL

2 NORMALLY OPEN

CONTACT AND

2 NORMALLY CLOSED

CONTACT WITH

5600

Ω

END OF LINE

RESISTOR

1 NORMALLY OPEN

CONTACT AND

1 NORMALLY CLOSED

CONTACT WITH

5600

Ω

END OF LINE

RESISTOR

ANY Z

TERMINAL

ANY COM

TERMINAL

This option can be selected if either Normally Closed (NC) or Normally Open (NO) detection
devices or contacts are being used.

2.9.3

Double End of Line (DEOL) Resistors

Double EOL loops allow the panel to determine if the zone is in alarm, tampered or faulted. Wire the zones
according to the following diagram:

ANY Z

TERMINAL

ANY COM

TERMINAL

ALARM

CONTACT

DOUBLE EOL CIRCUIT

1 NORMALLY CLOSED

CONTACT WITH

5600

Ω

END OF LINE

RESISTORS

This option can only be selected if Normally Closed (NC) detection devices or contacts are
being used

.....

Only one NC contact can be connected to each zone, multiple detection devices or contacts
on one loop is not allowed

.....

«
...
8
9
10
11
12
...
»

Summary of Contents for Power832

















































Reviews:

No comments