manualshive.com logo in svg

DSC Power832, Installation Manual, Page: 1 / 48

Share
Download
DSC Power832 Installation Manual Download Page 1

1

S E C T I O N  1

1.1

Specifications

Control Panel Specifications

Flexible Zone Configuration:

• 8 Fully Programmable Zones
• 37 Access Codes: 32 User, 1 System Master, 2 Partition Master and 2 Duress
• Expandable to 32 Zones
• Hardwired expansion available using the PC5108 Eight Zone Expansion Module
• Wireless expansion available using the PC5132 Wireless Zone Expansion Module (up to 32 wireless

zones, 900MHz, True Spread Spectrum Technology, Fully Supervised)

• Normally Closed, Single EOL, or Double EOL zone supervision
• 2-Wire Smoke Zone
• 27 Zone Types, 8 Programmable Zone Options
• 2 Partitions

Audible Alarm Output:

• Supervised Bell Output (current limited at 3 amps), 12 V

DC

• Steady or Pulsed Output

EEPROM Memory:

• Will not lose programming or system status on complete AC and Battery failure

Programmable Outputs:

• Up to 14 Programmable Voltage Outputs, 18 programmable options
• One High Current (300 mA) PGM output with 2 wire smoke detector capability on main panel
• Maximum Loop Current is 1.5 mA when the 2-wire smoke detector configuration is used
• One Low Current (50 mA) PGM output on main panel
• Eight Additional Low Current (50 mA) PGM outputs available using the PC5208 module
• Four High Current (1 Amp) PGM outputs Available Using the PC5204 module
• 1 PC5204 Output Fully Supervised for Siren Output

Powerful 1 Amp Regulated Power Supply:

• 500 mA Auxiliary Supply, 12 V

DC

• Positive Temperature Coefficient (PTC) components replace fuses
• Supervision for loss of AC Power, Low Battery
• Internal Clock Locked to AC Power Frequency

Power Requirements:

• Transformer = 16.5 VAC, 40VA
• Battery = 12 volt 4 Ah minimum rechargeable sealed lead acid

Remote Keypad Specifications:

• 4 Different Keypads Available:

- PC5508/KP5508 8 Zone LED Keypad

- PC5516/KP5516 16 Zone LED Keypad

- PC5532/KP5532 32 Zone LED Keypad

- LCD5500/KPL5500 Alphanumeric Keypad

• Each Keypad has 5 Fully Programmable Function Keys

• Connect up to 8 Keypads

• Four Wire (Quad) Connection to Keybus

• Built in Piezoelectric Buzzer

Digital Communicator Specifications:

• Supports all Major Formats including SIA and Contact ID

• Event Initiated Personal Paging

• 3 Programmable Phone Numbers

• 2 Account numbers

• Supports LINKS1000 Cellular Communication

• DTMF and Pulse Dialing

• DPDT Line Seizure

• Anti-jam Feature

• Split Reporting of Selected Transmissions to Each Telephone Number

System Supervision Features

The PC5010 continuously monitors a number of possible trouble conditions including:
• AC Power Failure

• Trouble by Zone

• Fire Trouble

• Telephone Line Trouble

• Low Battery Condition

• Bell Output Trouble

• Loss of Internal Clock

• AUX Power Supply Fault

• Tamper by Zone

• Failure to Communicate

• Module Fault (Supervisory or Tamper)

System Introduction

Summary of Contents for Power832

















































Reviews:

No comments