Draytek Vigor3200 Series User Manual Download Page 42

Page: 42 / 319

Vigor3200 Series User’s Guide

Physical Mode / Type

Display the physical mode and physical type of such WAN
interface.

Line Speed

Display the downstream and upstream rate of such WAN
interface.

Active Mode

Display whether such WAN interface is Active device or backup
device.

Backup WAN

Display the Backup WAN interface for such WAN when it is
disabled.

Note:

In default, each WAN is enabled.

WAN1 ~ WAN4 are fixed with physical mode of Giga Ethernet. Here we take WAN1 as an
example.

Enable

Choose

Yes

to invoke the settings for this WAN interface.

Choose

to disable the settings for this WAN interface.

Display Name

Type the description for such WAN interface.

Physical Mode

Display the physical mode of such WAN interface.

Physical type

You can change the physical type for WAN2 or choose

Auto

negotiation

for determined by the system.

Line Speed

If your choose

According to Line Speed

as the

Load Balance

Mode

, please type the line speed for downloading and

uploading for such WAN interface. The unit is kbps. The

Summary of Contents for Vigor3200 Series
































































































































































































































































































































Search results

Summary of Contents for Vigor3200 Series

Reviews:

Related manuals for Vigor3200 Series

Brands by name

Popular brands

Draytek Vigor3200 Series, User Manual

Search results

Summary of Contents for Vigor3200 Series

Reviews:

Related manuals for Vigor3200 Series

Brands by name

Popular brands