Draytek Vigor3200 Series User Manual Download Page 35

Page: 35 / 319

Vigor3200 Series User’s Guide

The online status shows the system status, WAN status, and other status related to this router
within one page. If you select

PPPoE

as the protocol, you will find out a link of

Dial PPPoE

Drop PPPoE

in the Online Status web page.

Detailed explanation is shown below:

Primary DNS

Displays the IP address of the primary DNS.

Secondary DNS

Displays the IP address of the secondary DNS.

LAN Status

IP Address

Displays the IP address of the LAN interface.

TX Packets

Displays the total transmitted packets at the LAN interface.

RX Packets

Displays the total number of received packets at the LAN interface.

WAN1~WAN5 Status

Line

Displays the physical connection (Ethernet) of this interface.

Name

Displays the name set in WAN web page.

Mode

Displays the type of WAN connection (e.g., PPPoE).

Summary of Contents for Vigor3200 Series
































































































































































































































































































































Search results

Summary of Contents for Vigor3200 Series

Reviews:

Related manuals for Vigor3200 Series

Brands by name

Popular brands

Draytek Vigor3200 Series, User Manual

Search results

Summary of Contents for Vigor3200 Series

Reviews:

Related manuals for Vigor3200 Series

Brands by name

Popular brands