Draytek Vigor3200 Series User Manual Download Page 106

Page: 106 / 319

Vigor3200 Series User’s Guide

Subnet Mask:

Type the subnet mask.

Gateway IP Address:

Type the gateway IP address.

Default MAC Address

: Click this radio button to use default

MAC address for the router.

Specify a MAC Address

: Some Cable service providers specify a

specific MAC address for access authentication. In such cases
you need to click the

Specify a MAC Address

and enter the

MAC address in the MAC Address field.

DNS Server IP Address

Type in the primary IP address for the router if you want to use

Static IP

mode. If necessary, type in secondary IP address for

necessity in the future.

Summary of Contents for Vigor3200 Series
































































































































































































































































































































Search results

Summary of Contents for Vigor3200 Series

Reviews:

Related manuals for Vigor3200 Series

Brands by name

Popular brands

Draytek Vigor3200 Series, User Manual

Search results

Summary of Contents for Vigor3200 Series

Reviews:

Related manuals for Vigor3200 Series

Brands by name

Popular brands