Draytek Vigor3200 Series User Manual Download Page 172

Page: 172 / 319

Vigor3200 Series User’s Guide

162

Below shows the items which are categorized under

Profile Name

Type a name for the CSM profile.

Select All

Click it to choose all of the items in this page.

Clear All

Uncheck all the selected boxes.

The profiles configured here can be applied in the

Firewall>>General Setup

and

Firewall>>Filter Setup

pages as the standard for the host(s) to follow.

Below shows the items which are categorized under

P2P

Summary of Contents for Vigor3200 Series
































































































































































































































































































































Search results

Summary of Contents for Vigor3200 Series

Reviews:

Related manuals for Vigor3200 Series

Brands by name

Popular brands

Draytek Vigor3200 Series, User Manual

Search results

Summary of Contents for Vigor3200 Series

Reviews:

Related manuals for Vigor3200 Series

Brands by name

Popular brands