Doka Staxo 40 Instructions For Assembly And Use Download

Page: 68 / 92

999805002 - 09/2018

General remarks

User Information

Load-bearing tower Staxo 40

Secondary-beam stabilisers

Secondary-beam stabilisers are used to prevent form-

work beams tipping over while panels are being laid on

them.

Advantages:

▪

Special claws to prevent slippage on the beam-

flange

▪

Needs only small commissioning quantities, as the

Secondary-beam stabilisers can be re-set in tandem

with the formwork erection cycle:

- approx. 20 Secondary-beam stabilisers 1
- approx. 10 Secondary-beam stabilisers 2

Note:

In certain special situations, (e.g. when forming inclined

floor-slabs), Secondary-beam stabilisers can also be

used for transferring horizontal loads.
For more information, please contact your Doka techni-

cian.

How to mount:

➤

Hang the Secondary-beam stabilisers into place with

an Alu beam fork H20.

The secondary beam is now held in place.

➤

Lay the formwork sheets.

➤

After the formwork sheets have been laid, unhook

and remove the Secondary-beam stabilisers with an

Alu beam fork H20.

Secondary-beam stabiliser 1

Secondary-beam stabiliser 2

98039-217-01

98039-217-02

98024-329-01

Summary of Contents for Staxo 40





























































































Search results

Summary of Contents for Staxo 40

Reviews:

Related manuals for Staxo 40

Brands by name

Popular brands

Doka Staxo 40, Instructions For Assembly And Use

Search results

Summary of Contents for Staxo 40

Reviews:

Related manuals for Staxo 40

Brands by name

Popular brands