manualshive.com logo in svg

doble Vanguard Instruments WRM-10P S2, User Manual, Page: 39 / 77

Share
Download
doble Vanguard Instruments WRM-10P S2 User Manual Download Page 39

REV 1.0

 

WRM-10P S2 USER’S MANUAL

 

 

35

 

 

 

 

 

 

h.

 

The following warning screen will be displayed: 

 

This warning is a reminder that the next sequence of test steps will run current through 

the test load and that caution should be exercised. 
Press any key to continue. 

i.

 

The following screen will be displayed: 

 

Press the 

[START]

 key to run the test. 

j.

 

The following screen will be displayed momentarily: 

 

After the WRM finishes its internal calibration, the following screen will be displayed: 

 

This is only an informational screen to remind the operator that a test is in progress. The 

display duration of this message depends on the size of the winding’s inductance. 

*XFMR CHARGING* 

 

    PLEASE WAIT... 
 

 

 

 

    CALIBRATING 
    PLEASE WAIT... 
 

 

 

 
 

-V1 & V2 TEST- 

 
 

 

 

"START" TO RUN TEST

OR 

"STOP" TO ABORT

**********WARNING********** 

DANGEROUS FLASH-OVER 

WILL OCCUR IF CABLES 

ARE DISCONNECTED! 

*************************** 

 

Summary of Contents for Vanguard Instruments WRM-10P S2














































































Reviews:

No comments