9024-065-Q-8-16
Sec:A3
12345678
ON
12345
ON
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
KEY
SWITCH
NO
NC
3 BUTTON
CONTROL
SW1
SW2
OFF
ON
POWER
P4
6
1 2 3 4 5 6 7 8 9 10
QUICK GUIDE: Terminal Descriptions
Low Voltage Common
Full Open
24 VDC - 250 mA max.
Open / Loop out
Low Voltage Common
Full Open
Low Voltage Common
Partial Open
Low Voltage Common
Reverse / Stop
Low Voltage Common
24 VDC Accessories / Maglock
Relay
Relay
Low Voltage Common
Bi-Parting
Bi-Parting
Common
Tracker Data
Tracker In
3 Button Station
•
Use a standard
4-wire
3-button
control station.
DoorKing’s
3-wire
3-button
control station
cannot
be used.
•
When using a 3-button control
station, the 3-pin jumper MUST
be set to
ON
position.
UL 325
See pages 24 - 26
3-Button
Station
Relay
Contacts
3 Button
LEDs
For long gate applications. An input
device connected to main terminal 8 will
open the gate to the partial open setting,
See page 22 for more information.
8
10
12
13 14
18
17
16
OPEN Beam Stop
CLOSE Beam Reverse
OPEN Edge/Beam Reverse
CLOSE Edge/Beam Reverse
Ground (Common)
Ground (Common)
OPEN
CLOSE
STOP
Common
•
lf SW 1,
switch 3
is
ON
, functions as a
normal full open input (Normal setting).
•
lf SW 1,
switch 3
is
OFF
, input to main
terminal 4 becomes the output from the
EXIT loop detector plugged into the EXIT
loop port. (Used for specialized functions).
ON
12
3
45678
SW 1
This input ONLY functions when gate is
fully
opened
or in the
closing cycle
.
•
When gate is closing: SW 1,
switch 4
is
OFF,
an input to main terminal 10 (eg: photo beam
gets obstructed) will
reverse
and open the gate.
Note:
If the auto-close timer is ON,
when gate reaches the open position,
timer will time out and close the gate.
•
When gate is closing: SW 1,
switch
4
is
ON,
an input to main terminal 10
(eg: photo beam gets obstructed) will
stop
the gate, then continue to close
the gate when input is clear (Used to
help prevent tailgating vehicles from unauthor-
ized entry). See page 21 for more information.
ON
12
3
4
5678
SW 1
Operation of relay is dependent on
setting of SW 1,
switches 6 and 7
.
Relay contacts
can be set for
Normally Open (NO) or Normally
Closed (NC) operation.
Contact rating is
1 amp maximum
at 24-volts DC.
ON
12
3
4
5
67
8
SW 1
NC
NO
4
ON
OFF
OPEN
STOP
CL
OSE
Main T
erminal Input LEDs
#19
#20
W
4
5
Main Terminal Input
LEDs Note:
The LED
that is beside the main
terminal wiring input
will light when that
terminal input gets
activated.
Main Terminal Input LEDs
W
M
M
M
L
tha
WE
M
M
M
L
th
WE
M
M
M
M
L
L
L
L
th
h
E
M
M
M
M
L
L
L
L
th
h
h
h
E
M
M
M
M
L
L
L
th
h
h
E
M
M
M
L
L
L
th
E
E
M
M
L
t
ER
R
M
M
t
ER
R
M
R
R
R
R
#2
#4
#6
#8
#10
ON
1
2
34567
8
SW 1
SW1,
switch 8 OFF
: 24-VDC,
500 mA constant power can be
provided for desired accessories
wired to terminal 12 when the
maglock is
NOT
used.
Photo
Sensor
Maglock
See page 28 for terminal wiring.
UL 325/3 Button 10-Pin Terminal
SW1,
switch 8
ON
: 24-VDC
Maglock
power is provided
except
when the gate is
opening
or
open
(Normally Closed function). 1 Amp Max.
19 20
Connects to a
DoorKing Tracker Expansion
Board
. Data will be reported about this
gate
operator’s SPECIFIC activity
to a DoorKing
access control system. A list of the events
will be “Tracked” and stored in the access
control system.
Bi-Parting Gates ONLY.
Connect secondary gate operator
main terminals 16-17-18 to primary main terminal
16-17-18 respectively. 16 & 17 wires
MUST
be twisted
together.
Primary operator is determined by pressing its
KEY SWITCH
FIRST
after powering up operators.
This establishes Primary/Secondary operator order.
16 & 17 wires
MUST
be twisted
18 wire COM
Quick Guide - 2
