34
Beginning work
Option 1
Option 2
Option 1 and 2
If you keep driving despite this warning:
• the brush unit and the squeegee will be raised from the floor after approx. 5
minutes.
• the suction unit will switch off after approx. 10 seconds (red display lights up
continuously).
• you still have approx. 10 minutes to run to the nearest mains socket before
the running drive switches off.
Cleaning method
Direct method:
Scrubbing and vacuuming in one pass.
Indirect working method:
Apply the cleaning solution first (only scrubbing), afterwards scrubbing and
vacuuming.
The cleaning methods are described in detail in the ”Method Card”. You can
obtain this from your TASKI partner.
Refilling the Flex tank
The rattling noise from the pump indicates that the Flex tank is empty.
Proceed as follows:
Recovery tank full indicator:
End of operation
Option 1
Option 2
Option 1 and 2
Empty and clean the recovery tank / Flex tank
The disposal of the dirty water or the cleaning solution must be carried out in
accordance with the national regulations and the regulations of the detergent
manufacturer .
Proceed as follows:
Caution:
Always wear non-slip shoes and appropriate work clothing while
working with this machine!
• Always hold the driver's handle with both hands
to ensure safe operation of the machine.
Caution:
Familarise yourself with the machine first by carrying out a few
driving trials in a free area!
• Stand on the platform.
Check that the Emergency Stop button has been released.
• Switch the machine on (Keyswitch to the Start position).
The indicators light up.
• Press the Start/Stop button.
The last cleaning settings used are stored and
will be re-started by pressing the Start/Stop
button.
• Press the brush unit button.
The indicators light up.
• Set the brush pressure with the +/- buttons (min. Level 1/ max. Level 3).
• Press the vacuum button.
The indicators light up.
The suction motor is started and the squeegee
is lowered.
• Press the solution button.
The indicators light up.
• Set the quantity of the cleaning solution using the +/- buttons (min. Level 1/
max. Level 6).
• Hold the driving handle with both hands.
• Set the machine in motion by gently pressing the speed controls.
The tools begin to rotate and the cleaning solution is fed through the centre.
When the last green display on the battery indicator goes out, an audible
signal is given and the red display blinks. Run the machine to the nearest
mains socket or to the battery charger.
Caution:
The manual brake release may only be operated on an even
surface, and a second person must always be present when
pushing the machine.
Start
Stop
Caution:
Do not clean without solution, as it could cause floor damage.
• Refill the machine, see Page 33.
• If the recovery tank indicator lights up, the
squeegee will be raised and the suction unit
switches off after 30 seconds.
• Drain the recovery tank, refer to Page 34.
• Press the Start/Stop button.
All functions will be stopped automatically.
The last setting to be used will be saved.
• The feed of cleaning solution stops and the tools lift off from the floor after
10 seconds.
• Drive on a few metres further in order to pick up the remaining dirty water.
• The squeegee lifts off after 20 seconds, and the suction unit runs for a
further 10 seconds.
• Stop the supply of cleaning solution by pressing
the solution dosing control button.
• Drive a few metres further to avoid dripping.
Very important when using contact pads!
• Press the brush unit button.
The tools stop and rise up from the floor.
• Drive on a few metres further in order to pick up the remaining dirty water.
• Now switch off the vacuum unit.
The squeegee lifts, and the suction unit
continues to run for approx. 10 seconds.
Always drain and clean the recovery tank every time you use the
machine.
If the dirty water is allowed to stand, unpleasant smells and
deposition of the dirt will take place after a few hours.
• Switch the machine off using the keyswitch and remove the key.
Start
Stop
