DITEC Entre Matic ENERGY, Installation Manual

Page: 25 / 68

- 25 -
0DT828 28/10/2010
IMPUT
Command Function Description
1 2 N.O Automatic closing Permanently closing the contact enables automatic closing.
1 3 N.O Opening The closure of the contact activates an opening operation.
1 4 N.O Closing The closing manoeuvre starts when the contact is closed.
41 40 N.C Reversal safety device Opening the safety contact triggers a reversal of the movement (reopening) during a closing operation.
1 8 N.C Reversal safety device Opening the safety contact triggers a reversal of the movement (reopening) during a closing operation.
1 9 N.C Stop Opening the safety contact stops the current operation.
1 9 N.O Non-pulse command Permanently opening the safety contact enables the operation by non-pulse command
In this state, the opening (1-3/1-20) and closing (1-4) controls function only if held in the pressed position,
and the automation stops when the controls are released.
All safety switches, the step-by-step control and the automatic closing function are disabled.
1 20 Partial opening The closing of the contact activates a partial opening operation of the duration set with the RP trimmer.
Once the automation stops, the partial opening control performs the opposite operation to the one
performed before stoppage.
0 11 N.C Closure limit switch The opening of the limit switch contact stops the closure operation.
0 12 N.C Limit switch slowdown The opening of the limit switch contact activates the slowdown in opening.
0 13 N.C Opening limit switch The opening of the limit switch contact stops the opening operation.
Button LED
Starts the opening operation. The green LED on indicates the presence of the 24 V=power supply.
Starts the partial opening operation.
Starts and stops the STOP operation.
the red LED on indicates that the STOP has been activated.
the fl ashing red LED indicates that the safety devices have been activated.
Starts the closing operation.
KEYBOARD
Output Value Description
1 +
0 -
24 V= / 0,5 A
Accessories power supply.
Power supply output for external accessories, including automation status lamp.
LAMP 230 V~ / 50 W
Flashing light (LAMP).
Activated during opening and closing operations.
-F +F
24 V= / 1,2 A
200V= / 0.3 A
Electric motor brake.
The output is active for the duration of both the opening and closing operation.
230 V~ / 6 A
Three-phase motor.
Connect the contact of the motor circuit breaker in series to the limit switch.
Note: if the direction of rotation of the motor is incorrect for the desired direction of movement, swap the
L2 and L3 phases.
U W V
M
3 ~
OUTPUTS
ON
SEGNALAZIONI
LED On
DL1 (2) Automatic closing
DL2 (3) Opening
DL3 (4) Closing
DL4 (9) Stop
DL5 (20) Partial opening
DL6 (40) Safety edge
LED On
DL7 Stop push button
DL8 (8) Closing Safety
DL9 (13) Opening limit switch
DL10 (12) Slowing down limit switch
DL11 (11) Closing limit switch
DL12 Flashing lamp
LED On
DL13 Run OK
DL14 Fault
DL15 Autotest
DL16 Brake
DL17 Cycles counter
C
B
A
B
C
300
A
¾
Adjustment limit switch
1. Set the deceleration ramps to zero. (T5 - T6)
2. Calibrate limit switch (C) on the geared motor so that the door stops
approximately 200-300mm from the closure point respectively.
3. Calibrate limit switch (A), at the wished quote.
4. Calibrate slowdown limit switch (B) in such a way that it engages at
approximately ¾ of the opening stroke.
5. Calibrate the opening speeds using trimmer (T3) and closure (T4).
6. Calibrate the opening (T5) and closure (T6) trimmers of the deceleration
ramps in such a way as to cause stopping in the actual door open and
door closed positions.
EN