manualshive.com logo in svg

DirecTV Advanced Installation Meter, User Manual

Share
Download
DirecTV Advanced Installation Meter User Manual Download Page 9

1 Getting Started

AIM User’s Manual

2

Using This Manual

Overview

Read this manual completely before using your AIM. Also, retain this manual for 

future reference.
For information to help you get started using your AIM, see the sections below:

ƒ

Getting to Know Your Meter

, starting on 

page

 

5

.

This section provides an overview of the AIM, including information about the 

meter and its accessories, its display and buttons, and how to navigate through 

the screens on the meter.

ƒ

Powering Your Meter

, starting on 

page

 

10

.

This section provides instructions for how to turn on and turn off the meter, an 

overview of the meter’s power-saving features, and instructions for how to 

charge the battery and replace the battery.

ƒ

Getting Technical Support

, starting on 

page

 

17

.

This section describes how to access technical support.

ƒ

Safety Instructions

, starting on 

page

 

18

.

This section provides important safety instructions for using the AIM.

ƒ

Technical Specifications

, starting on 

page

 

19

.

This section provides information about the dimensions, capabilities and 

operating range of the AIM.

ƒ

Spare Parts List

, starting on 

page

 

20

.

This section provides a list of replacement parts that can be ordered for the AIM.

Summary of Contents for Advanced Installation Meter





























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands