DirecTV Advanced Installation Meter User Manual Download Page 24

Page: 24 / 92

1 Getting Started

AIM User’s Manual

Getting Technical Support

When you need instructions for using the AIM, your first resource for help is this

manual. If you cannot find the information you need, you can:

Go to the DIRECTV Satellite Installer website or other websites provided by

DIRECTV. DIRECTV websites contain product specifications and information, tips,

release information, marketing information, Frequently Asked Questions (FAQs),

bulletins and other technical information. You can also check these websites for

product updates.

Contact Trilithic technical support. Technical support is available Monday

through Friday from 8:00 am to 5:00 pm EST at 1-317-895-3600 or

1-800-344-2412 (toll free). You can also e-mail technical support at

[email protected]

For a quicker support response when calling or sending e-mail, provide the

following information:

– your name and company name
– the technical point of contact (name, phone number, e-mail)
– the AIM serial number, firmware and hardware version numbers
– a detailed description of the problem you are having, including any error or

information messages

Summary of Contents for Advanced Installation Meter





























































































Search results

Summary of Contents for Advanced Installation Meter

Reviews:

Related manuals for Advanced Installation Meter

Brands by name

Popular brands

DirecTV Advanced Installation Meter, User Manual

Search results

Summary of Contents for Advanced Installation Meter

Reviews:

Related manuals for Advanced Installation Meter

Brands by name

Popular brands