DirecTV Advanced Installation Meter User Manual Download Page 10

Page: 10 / 92

1 Getting Started

AIM User’s Manual

Instructions for using the AIM’s features are provided in the following chapters:

Chapter 2: Setting Up the Meter

, starting on

page

Before you use your AIM, you need to enter registration information and

confirm the meter’s settings. This chapter provides instructions for entering

registration information, as well as setting the meter’s volume, display contrast

and brightness, time limits for power-saving features, and date and time.

Chapter 3: Setting Up a Job

, starting on

page

Before you perform tasks for an installation using the AIM, you can set up the

information for the job. This chapter provides instructions for entering the

account number, selecting the ODU type, selecting the switch type, and entering

the zip code.

Chapter 4: Installing an ODU

, starting on

page

The AIM guides you through the steps for aligning and performing follow-up

Extended Installation Verification (EIV) for each ODU. This chapter provides

instructions for how to complete these processes using the AIM.

Chapter 5: Performing EIV

, starting on

page

You can perform Extended Installation Verification (EIV) at selected points in the

distribution network to quickly confirm that the installation is satisfactory for all

supported orbital slots. EIV is an easy way to pinpoint any potential problems

with the installation. This chapter provides instructions for performing EIV at the

ODU and other locations in the distribution network.

Summary of Contents for Advanced Installation Meter





























































































Search results

Summary of Contents for Advanced Installation Meter

Reviews:

Related manuals for Advanced Installation Meter

Brands by name

Popular brands

DirecTV Advanced Installation Meter, User Manual

Search results

Summary of Contents for Advanced Installation Meter

Reviews:

Related manuals for Advanced Installation Meter

Brands by name

Popular brands