DirecTV Advanced Installation Meter User Manual Download Page 54

Page: 54 / 92

Performing EIV

Extended Installation Verification (EIV) can be performed at any point in the

installation to quickly confirm that the installation is satisfactory for all supported

orbital slots. EIV is an easy way to pinpoint any potential problems with the

installation. The AIM guides you through the steps for the testing.
To

perform the Extended Installation Verification (EIV):

Start the job for the installation (“Starting a Job” on

page

From the

HOME

screen, press

EIV

to go to the

SELECT CONFIGURATION

screen.

Use

to highlight the equipment configuration for the installation and

press

SELECT

to go to the

MEASUREMENT LOCATION

screen.

Use

to highlight the location where you are testing.

Connect the AIM ODU F connector at the point in the distribution network

where you want to test. Then press

SELECT

to go to the

EIV

screen.

Example:

To test between the ODU and the

multiswitch, disconnect the cable connecting

the ODU to the multiswitch and connect it

to the AIM’s ODU F connector.

Summary of Contents for Advanced Installation Meter





























































































Search results

Summary of Contents for Advanced Installation Meter

Reviews:

Related manuals for Advanced Installation Meter

Brands by name

Popular brands

DirecTV Advanced Installation Meter, User Manual

Search results

Summary of Contents for Advanced Installation Meter

Reviews:

Related manuals for Advanced Installation Meter

Brands by name

Popular brands