DirecTV Advanced Installation Meter User Manual Download Page 46

Page: 46 / 92

4 Installing an ODU

AIM User’s Manual

Task A. Installation Setup

To perform the installation setup:

Start the job for the installation (“Starting a Job” on

page

From the

HOME

screen, press

INSTALL

The

PRE-CONFIGURE ODU

screen appears showing the default azimuth and

elevation coordinates for the job. If appropriate, the default tilt coordinate also

appears.

Perform the ODU site survey. Using the AIM azimuth and elevation coordinates,

confirm that the selected location has a clear line-of-sight to the supported

orbital slots (see “ODU Installation Tasks” on

page

Install the ODU according to the DIRECTV procedure.

Connect the AIM’s ODU F Connector to the ODU’s LNB output.

Press

NEXT

on the

PRE CONFIGURE ODU

screen.

If the installation includes two ODUs,

the

SELECT ODU

screen appears.

Use

to highlight the ODU to align and press

SELECT

to continue.

Note:

The default coordinates for the job are

based on the ODU type and zip code selected

for the job.

Summary of Contents for Advanced Installation Meter





























































































Search results

Summary of Contents for Advanced Installation Meter

Reviews:

Related manuals for Advanced Installation Meter

Brands by name

Popular brands

DirecTV Advanced Installation Meter, User Manual

Search results

Summary of Contents for Advanced Installation Meter

Reviews:

Related manuals for Advanced Installation Meter

Brands by name

Popular brands