DirecTV Advanced Installation Meter User Manual Download Page 32

Page: 32 / 92

2 Setting Up the Meter

AIM User’s Manual

Changing the Display Contrast or Brightness

You can change the display contrast and display brightness settings for your AIM.
To change the display contrast or brightness:

Press

CONFIG

to go to the

CONFIGURATION

screen.

Use

to highlight

Settings

and press

SELECT

to go to the

SETTINGS

screen, which shows the current settings for the meter.

Use

to highlight

Contrast

Brightness

and press

SELECT

to go to the

CONTRAST

BRIGHTNESS

screen.

Use

to select the desired setting. Then press

ENTER

to return to the

SETTINGS

screen.

Tip:

You can press

to quickly adjust the

display contrast or display brightness settings.

Summary of Contents for Advanced Installation Meter





























































































Search results

Summary of Contents for Advanced Installation Meter

Reviews:

Related manuals for Advanced Installation Meter

Brands by name

Popular brands

DirecTV Advanced Installation Meter, User Manual

Search results

Summary of Contents for Advanced Installation Meter

Reviews:

Related manuals for Advanced Installation Meter

Brands by name

Popular brands