Directed Electronics READY REMOTE 24927 Owner'S Installation Manual Download

Page: 74 / 95

Owner’s Guide

Now that the installation is complete and tested, it is time to
learn about the many outstanding features that are included in
your remote start, security and convenience system.

Remote Start Features

➤

Remote Start your engine to warm or cool your vehicle
before driving

➤

Quick Stop Mode will keep the vehicle interior warm or
cool during short trips away from the vehicle

➤

Daily Start for convenient engine warm up at a specific
time the following day

➤

Vacation Mode maintains battery level when the vehicle
is parked for extended periods

Security and Convenience features

➤

The built in alarm will keep your vehicle secure when
parked and remote started

➤

Keyless entry and starter kill outputs for convenience
and security

➤

Panic Mode feature to call for help if you are threatened
while in or near your vehicle

➤

CarFinder feature helps you find your vehicle in dark
parking lots

➤

Valet Mode will temporarily defeat the remote start and
alarm features, but leave the convenience feature avail-
able

Summary of Contents for READY REMOTE 24927
































































































Search results

Summary of Contents for READY REMOTE 24927

Reviews:

Related manuals for READY REMOTE 24927

Brands by name

Popular brands

Directed Electronics READY REMOTE 24927, Owner'S Installation Manual

Search results

Summary of Contents for READY REMOTE 24927

Reviews:

Related manuals for READY REMOTE 24927

Brands by name

Popular brands