Directed Electronics READY REMOTE 24927 Owner'S Installation Manual Download Page 60

Page: 60 / 95

6. Unlock Pulses: Selects the number of pulses when Unlocking the
doors.

1 Pulse

: The Door Unlock output will be a single pulse

for the programmed duration.

2 Pulses

: The Door Unlock output will be a double pulse

for the programmed duration.

7. Lock Duration: Selects the duration of the pulses when Locking
and Unlocking the doors.

Short Pulse

: The Door Lock & Unlock outputs will be

800mS in duration.

Long Pulse

: The Door Lock & Unlock outputs will be a

3.5 seconds in duration.

8. Alarm Mode: Selects if the alarm functions are active or
bypassed.

: Alarm functions are operational as described

Off

: Alarm functions are NOT operational, but conve-

nience features and Remote Starter still operate
normally.

9. Auto Re-arming: Selects if the units will automatically Re-
arm/lock itself if the trunk and door are not activated after trans-
mitter disarm/unlock.

Off

: The unit WILL NOT automatically Arm/Lock the

doors after transmitter Disarm/Unlock.

: The unit will automatically Arm/Lock the doors 120

seconds after transmitter Disarm/Unlock if Alarm Inputs
1 or 6 remain idle.

Summary of Contents for READY REMOTE 24927
































































































Search results

Summary of Contents for READY REMOTE 24927

Reviews:

Related manuals for READY REMOTE 24927

Brands by name

Popular brands

Directed Electronics READY REMOTE 24927, Owner'S Installation Manual

Search results

Summary of Contents for READY REMOTE 24927

Reviews:

Related manuals for READY REMOTE 24927

Brands by name

Popular brands