Directed Electronics READY REMOTE 24927 Owner'S Installation Manual Download | Manualshive

Page: 80 / 95

background image

81

© 2 0 0 7 D i r e c t e d E l e c t r o n i c s

To de-activate Daily Start:

➤

Press and hold the

&

buttons on your trans-

mitter for more than 3 seconds

➤

Activate Vacation Mode

➤

The parking lights will flash 4 times to confirm Daily
Start has been de-activated. (The Horn/siren will not
chirp)

Vacation Mode

Vacation mode is a valuable feature designed to maintain normal
operating conditions when the vehicle is parked for extended
periods. Vacation mode will monitor and automatically start the
engine any time the system detects extremely low battery voltage
or temperatures (See Programming Section for available low
temperature settings).

To activate Vacation Mode:

➤

Press and hold the

&

buttons on your trans-

mitter for more than 3 seconds

➤

The parking lights will flash 5 times and the Horn/Siren
will chirp once to confirm Vacation Mode is activated.

➤

Your vehicles’ battery level and interior temperature will
be monitored, and the engine will automatically start up
to 8 times.

➤

Temperature: the system will check the interior temper-
ature and start if required every three hours

➤

Battery level: the system will start the engine immedi-
ately when the battery level drops below 11.5 volts.

«
...
78
79
80
81
82
...
»

Summary of Contents for READY REMOTE 24927
































































































Reviews:

No comments

Related manuals for READY REMOTE 24927

Brand: Zamel Pages: 23

Brand: Zamel Pages: 2

SmartStuff Series

Brand: TCP Pages: 2

Brand: FUTABA Pages: 16

Brand: CAME Pages: 16

BLUETOOTH MEDIA REMOTE

Brand: Targus Pages: 24

Brand: Radio Shack Pages: 59

Multi-Channel Remote Control

Brand: Heath Zenith Pages: 12

Brand: Radioenge Pages: 6

Premium Remote Control

Brand: Dell Pages: 21

Brand: Dell Pages: 2

Brand: Spectravision Pages: 8

Brand: Spectravision Pages: 12

Brand: SystemAir Pages: 73

Brand: Universal Remote Control Pages: 1

UR4U-MDVR2B - SPECS SHEET

Brand: Universal Remote Control Pages: 2

Brand: UTAS Pages: 34

Brand: Assa Abloy Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands