Directed Electronics READY REMOTE 24927 Owner'S Installation Manual Download Page 8 | Manualshive

Page: 8 / 95

background image

9

© 2 0 0 7 D i r e c t e d E l e c t r o n i c s

System Maintenance

The system requires no specific maintenance. Your transmitter
is powered by a miniature 12-volt battery (type 23A) that will
last approximately one year under normal use. When the
battery begins to weaken, the operating range will be
reduced.

FCC/Id Notice

This device complies with Part 15 of FCC rules. Operation is
subject to the following conditions: (1) This device may not
cause harmful interference, and (2) This device must accept
any interference received, including interference that may
cause undesirable operation.

Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to
operate this device.

Warning! Safety First

The following safety warnings must be observed at all times:

When properly installed, this system can start the vehicle
via a command signal from the remote control trans-
mitter. Therefore, never operate the system in an area
that does not have adequate ventilation. The following
precautions are the sole responsibility of the user;
however, the following recommendations should be made
to all users of this system:

1. Never operate the system in an enclosed or partially

enclosed area without ventilation (such as a garage).

➜

➜

«
...
6
7
8
9
10
...
»

Summary of Contents for READY REMOTE 24927
































































































Reviews:

No comments

Related manuals for READY REMOTE 24927

Brand: Climatisation Pages: 52

Brand: Fantini Cosmi Pages: 25

Brand: EVERSPRING Pages: 3

Brand: Webasto Pages: 12

Brand: A&D Pages: 38

Brand: Valeo Pages: 8

Brand: Cirrus Pages: 8

Brand: Toshiba Pages: 5

Brand: Toshiba Pages: 8

Brand: Toshiba Pages: 2

RBC-AX32UM(W)-E

Brand: Toshiba Pages: 2

Brand: Toshiba Pages: 19

Brand: Toshiba Pages: 21

Brand: Toshiba Pages: 2

Brand: Toshiba Pages: 6

Brand: Toshiba Pages: 16

Brand: Toshiba Pages: 8

Brand: Toshiba Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands