Directed Electronics READY REMOTE 24927 Owner'S Installation Manual Download

Page: 77 / 95

When you are ready to drive the vehicle:

➤

Insert the ignition key and turn it to the ON (not the
START) position.

➤

Press the brake pedal. The remote start will shut down
and the engine will continue to run.

The remote start can be shut down in several ways for convenience
by the user or for safety by the shut down inputs.

To shut down remote start:

➤

Press the transmitter

button twice.

➤

Pulse the activation input wire twice

➤

Step on the brake.

Note!

If the brake pedal is pressed before the key is

in the ON position, the engine will shut down.

Important!

It is unsafe to operate a vehicle's motor

in a garage or other closed off area. Breathing the
exhaust from the vehicle is hazardous to your health.
Never activate the remote start in an enclosed space.

Important!

Never remote start your vehicle when the

keys are in the ignition, except when activating
Quick Stop mode. Never start the vehicle if it is not
in PARK and the Parking brake is not set.

Note!

If the lights flash more than once and the

engine does not start, refer to the No Start
Diagnostics for the cause.

Summary of Contents for READY REMOTE 24927
































































































Search results

Summary of Contents for READY REMOTE 24927

Reviews:

Related manuals for READY REMOTE 24927

Brands by name

Popular brands

Directed Electronics READY REMOTE 24927, Owner'S Installation Manual

Search results

Summary of Contents for READY REMOTE 24927

Reviews:

Related manuals for READY REMOTE 24927

Brands by name

Popular brands