Directed Electronics READY REMOTE 24927 Owner'S Installation Manual Download

Page: 55 / 95

Feature Menu 1 Descriptions

1. Engine Monitoring: Defines how the engine is monitored while
the Remote Start is active.

No Tach

: The battery voltage will be used to monitor the

engine while Remote Start is active.

Tachometer

: The tachometer will be used to monitor

engine speed while Remote Start is active.

2. Run Time

15 minutes:

The Remote Starter will shut down after it

has been active for 15 minutes.

30 minutes

: The Remote Starter will shut down after it

has been active for 30 minutes.

3. Crank Time: Will be in effect only when Engine Monitoring is
"No Tach" and affects the duration of the "Yellow" Starter Output
wire.

Normal Crank:

The Starter output will be 700mS.

Extra Crank:

The Starter output will be 1 second.

Super Crank:

The Starter output will be 1.4 seconds.

Mega Crank:

The Starter output will be 2.1 seconds.

4. Ignition 2 Output: This controls the output type of the high
current "Green" Ignition 2 output wire.

Ignition 2:

Output will match the Blue Ignition 1

input/output wire operation during remote start.

Accessory 2:

Output will match the White Accessory 1

operation during remote start.

Summary of Contents for READY REMOTE 24927
































































































Search results

Summary of Contents for READY REMOTE 24927

Reviews:

Related manuals for READY REMOTE 24927

Brands by name

Popular brands

Directed Electronics READY REMOTE 24927, Owner'S Installation Manual

Search results

Summary of Contents for READY REMOTE 24927

Reviews:

Related manuals for READY REMOTE 24927

Brands by name

Popular brands